EIM-2 type
View favorites See the comparison
It is an emergency shutoff valve device for earthquake disaster countermeasures that is attached to fuel pipes and various storage tanks and does not require external power such as electric signals and shuts off fluid only by the operating force of the seismic sensor due to earthquake motion.
When the seismic sensor is activated, it acts on the trip mechanism of the shutoff valve via the release mechanism, and the valve closes. Restoration is a safer recovery method because the shutoff valve is opened manually after operating the knob of the seismic sensor.
Where to use
Fuel supply lineVarious storage tanks

Major features

  • Since it is a mechanical shut-off valve, there is no need for power failure countermeasures (emergency power supply) or electrical equipment work. (Except with switch for open / close signal)
  • Since there is no risk of a secondary disaster due to a short circuit in electricity or heat generation, the power supply and explosive dangerous place (when using the limit switch signal in the explosive dangerous place, use the explosion-proof limit switch) and the power supply It can also be used in non-mountainous areas.
  • Since the seismic sensor and shutoff valve are installed separately, the seismic sensor can be mounted on a solid stand or a sturdy wall surface that is separate from the piping system, so there is no malfunction due to piping vibration.

specification

Product code EIM2-VA
Valve type Mechanical
type Made of stainless steel
Actuation Valve closed when the seismic sensor is activated (manual shutoff valve is opened after the seismic sensor is restored)
Nominal diameter 15-200 (1/2-8)
Applicable fluid Fuel oilFor fuel oil and light oil, the material of the main body may be specified depending on the destination (Ministry of Land, Infrastructure, Transport and Tourism, Ministry of Defense, etc.), so please check and specify the material. For gasoline, please contact us. ·gasFor gas, the disc is synthetic rubber.Please contact us when using with fuel gas. ·waterWhen using it for a water supply device, use EIM-2N, 3N type, which conforms to the performance standards of the Waterworks Law. ·airFor gas, the disc is synthetic rubber. ·oilFor fuel oil and light oil, the material of the main body may be specified depending on the destination (Ministry of Land, Infrastructure, Transport and Tourism, Ministry of Defense, etc.), so please check and specify the material. For gasoline, please contact us. ·(vaporThe fluid temperature of 180 ℃ or less (for steam) is manufactured by metal touch of the valve body. )
Fluid temperature 5-60 ℃The fluid temperature of 180 ℃ or less (for steam) is manufactured by metal touch of the valve body.
Applicable pressure 1.0MPaPlease contact us when using with fuel gas.
Protective structure Dust-proof type, for indoor use (When using outdoors, please use with a rain-proof cover.)Please contact us for rainproof covers (steel plate, stainless steel).
Ambient temperature -10 to 50 ° C (cannot be frozen)
End connection JIS 10K FF flange
Mounting posture Upright mounting on horizontal piping
Applicable differential pressure limit Nominal diameter 15 to 25: 1.0 MPa or less
Nominal diameter 32-40: 0.7MPa or less
Nominal diameter 50: 0.5 MPa or less
Nominal diameter 65: 0.2MPa or less
Nominal diameter 80: 0.2MPa or less
Nominal diameter 100: 0.1 MPa or less
Nominal diameter 125: 0.1 MPa or less
Nominal diameter 150: 0.05MPa or less
Nominal diameter 200: 0.04MPa or less
Allowable leakage amount None (visual pressure gauge)
Material body SCSPlease contact us for FC and SCPH main units.
Material Valve body SUS
Material disc PTFE
Seismic device operating method Weight magnet type (mechanical type)
Seismic device operation display Seismic sensor main unit display window Green: Warning display Red: Operation display
Seismic device reset method By rotating the "knob" on the front of the seismic sensor
Seismic sensor Seismic detection function Operating acceleration: 200 gal (equivalent to seismic intensity 5+)
Seismic device operation check Manual operation by rotating the "knob" on the front of the seismic sensor
Seismic device accuracy check Confirmation of operating angle by tilting the seismic sensor
Seismic device weather resistance Simple drip-proof structure-For indoor use (When using outdoors, please use the one with a special box.)Seismic sensors are also manufactured with a special box for outdoor installation (steel plate, stainless steel).
Seismic device operating temperature range -10 to 50 ° C
Seismic device Operating humidity range 90% RH or less
Seismic device release length In addition to 1,000 mm (applicable straight line distance 500 to 700 mm), according to the release length tableIf the seismic sensor is below the shutoff valve, use a release length of 1,800 mm. (Refer to page 381 for installation.)
  • We also manufacture one or two limit switches. (Electrical work is required.)
  • We also manufacture with an explosion-proof limit switch. (When ordering, please specify the outer diameter of the cable you are using.)
  • We can also manufacture an emergency shutoff system that can control two shutoff valves at the same time with one seismic sensor. (Delivery form is 1 dedicated seismic sensor and 2 shutoff valves.) Please contact us for details.

Download materials

Download materials

Common to all product symbols

EIM-2 Catalog

EIM-2 Price List

EIM-2 outline drawing

EIM-2 Instruction Manual

Frequently Asked Questions and Explanations

Is it possible to change the operating acceleration setting locally?

The operating acceleration cannot be changed in the field. Please contact us when ordering.

Is it possible to extract the operating signal?

EIM-2,3 Leeds is also manufactured with a limit switch (no voltage) as an option. The EIM-7 series has a limit switch (no voltage) on the closed side as standard.

Do you need a power supply?

The mechanical emergency shutoff valve does not require external power such as electrical signals, and does not require a power source because it operates only with the operating force of the seismic sensor due to seismic motion.

Inquiries about this product

Please use this form for product questions and technical inquiries.
If you would like to contact us by phone, please contact VENN's sales office.

We will strictly manage the personal information of our customers based on our "Personal Information Protection Management Regulations" and will not use it for anything other than responding to inquiries and consultations without the consent of the customer.
Please check our privacy policy.

Please cooperate with the questionnaire

We will use your opinions as a reference to make the website easier to understand and useful, so we ask for your cooperation.

Was this page helpful?

How easy was it to find the page you were looking for on this site?

How was the page easy to understand about this site?

Thank you for your cooperation

Added to Favorites View Favorites

close

Added to Download BOX Download BOX

close

Search tips

Products with different symbols depending on the product specifications are indicated by □.
When searching, please search by inputting up to the first character after the "-" (hyphen).

Notation on catalogs and websites

RD44N-F □

Contains characters that indicate pressure classification and options.

No hits in product search
RP7-FL
Hit in product search
RP7-FL
You can also search by product name or model.
product name
"Reducing valve", "solenoid valve", "safety valve", etc.
Model
"RP-6", "RD-31N", "SL-37", etc.